How to Design Hot Elbow Mandrel? 返回首頁

                              As a professional Hot Elbow Machine Supplier, today we would like to share with you how to design hot elbow mandrel. I hope you can learn about the methods through this article.


                              1.Hot Elbow Forming Technology

                              The concept of hot elbow forming technology is based on the metal material plasticity deformation remains the same to design, that is ,mother pipe volume is equal to elbow volume.


                              Hot Elbow Machine Supplier


                              No.1 Elbow

                              No.2Induction Heating Coil

                              No.3 Heat Preservation Device

                              No.4Mandrel

                              No.5Pusher

                              No.6 and 8 Clamp Part for mandrel rod

                              No.7 Mandrel Rod

                              No.8 Mother Pipe

                              No.9 Loading Part

                              No.10 Driven Part

                              No.11 Foundation

                              ①Loading Step: We can take the steel mother pipe go through the mandrel rod , one rod can hold fully ,exactly number depends on the length of mother pipe , normally one hot elbow machine will make a short range of elbow .Then driven part will push them to the front mandrel without induction heating .

                              ②Induction Heating Step :When arrive at the setting temperature , then hot forming with the pusher pushing .Mainly two big metal deformation one is diameter bigger and the other one is bending .

                              ③Forming Step : When the elbow left the mandrel , then one elbow is finished .

                              When forming process , the pushing force will force the mother keeps Radial compensation, so the wall thickness is almost no difference with the mother pipe .And intrados and extrados are almost the same .


                              2.How to define the dimension of hot elbow mandrel dimension

                              2.1Mother Pipe model confirm

                              Let us take one example .Elbow Size :φ558.8mm×22.2mm Bending radius 838mm . and the wall thickness/OD is 22.2/558.8=0.03mm. It belongs to the thin elbow range .So the formula is as follows;


                              Do: Mother Pipe OD mm

                              D:Elbow OD mm 558.8mm

                              R:Bending Radius,mm 838mm

                              Do=418mm

                              Since φ418mm is close to φ406.4mm,and almost no wall thickness changing so we can choose φ406.4mm ×22.2mm.


                              2.2Define the dimension of mandrel

                              Mandrel is including three phases one is filtration process ,deformation process ,sizing process.


                              2.21: Filtration Process:the function is to position the mother pipe .

                              d1 = mother pipe OD -(2×mother pipe wall thickness + x)

                              X: the gap between the mother pipe ID and the mandrel , X=6mm)

                              So d1=406.4-(2×22.2+6)=356mm

                              Filtration length L=2d1=2×356=712mm


                              2.22:deformation Process

                              This phase mother is happening OD changing and bending ID changed to Elbow ID , mother pipe OD changed to elbow OD .bending radius changed to elbow radius .,then we calculate the mandrel dimension .We can define the 45 degree .

                              d2=elbow OD -2×Elbow wall thickness

                              =558.8-2×22.2=514.4mm

                              Considering the thermal expansion to d2=516mm

                              H: from the 90 degree elbow end to Filtration center height

                              H=R+d2/2-d1/2

                              =838+516/2-356/2=918mm

                              Deformation Extrados bending radius:

                              R1=R+d2/2=838+516/2=1096mm

                              Deformation Intrados bending radius:

                              R2=(R-d2/2)+2(d2-d1)/Sin45degree =1033mm

                              Sizing Process :

                              This process is to make the elbow OD and bending better .

                              Sizing extrados bending radius: R3=R1=R+d2/2=1096mm

                              Intrados bending radius: R4=R-d2/2=580mm


                              Hot Elbow Machine Supplier


                              End

                              If you want to learn more about hot elbow forming , please feel free to contact me .


                              Contact: Mr.Dong 

                              Email: lmdzjxc@lmdzzjxc.com

                              Web: www.5jiuxi.icu 

                              Mobile:0086 13931703233


                              上一篇:The Failure Of The Bender Should Be Repaired In Time

                              下一篇:The Principle Of Induction Heating Pipe Bending Machine

                              TEL:0086-139-31703233
                              Fax : 0086-317-6817833
                              Email:lmdzjxc@lmdzjxc.com
                              Address:Xiwang New District ,Mengcun Hui Autonomous County, Hebei province,China. sitemap google

                              Facebook Linkedin Pinterest 冀ICP備12017094號-2
                              久艹在线